This mini audio amplifier will test the audio stages in amplifiers
such as the front end of FM bugs. You can also use it on lots of our
other projects as well as the output
stages of radios. It is a very handy piece of test equipment and will
make a perfect addition to your collection.
MINI BENCH AMPLIFIER
Some of the projects you can test with the Mini Bench Amplifier are tone circuits while others are audio
circuits. Tone circuits and audio stages are surprisingly difficult to
test unless you have an audio probe or a CRO.
A CRO is an ideal piece of equipment but if your budget does not
extend this far, the next best thing is an audio probe.
MINI BENCH AMPLIFIER
There are lots of things that can go wrong with an audio stage. It can
produce distortion or a “hollow” sound, go weak or simply fail
Likewise tone circuits can present a number of faults and it is very
handy to be able to “hear” what is going wrong.
It is not sufficient to measure the DC voltages on these stages. This
only gives a partial picture of the conditions and does not tell you the
quality of the audio being processed. To determine this you need a piece
of test equipment that will let you see or hear what is being processed.
Firstly we will cover the benefits and problems of using a CRO.
The main problem with seeing the waveform on a CRO is you have to
interpret what you see and work out if distortion is present and where it
is coming from. Believe me, this is harder to do than you think.
Let me give some examples from a TV service-man friend. He has
serviced some 35,000 TV sets over a period of 15 years and in that time
he has used a CRO on a number of occasions to try and find faults in
One particularly troublesome audio fault occurred in an old black and
white TV set, so he got out the CRO to try and solve the problem.
The audio was weak and distorted but since the signals around IF
transformers are very small even when the circuit is functioning
correctly, he could not locate the fault.
Audio waveforms are seldom shown on circuit diagrams and it is
difficult to know if the signal you are viewing on a CRO is faulty or
To fix the set he had to resort to the old tried-and-proven method of
replacing components one-by-one. The fault turned out to be a 100p styro
in one of the sound-IF cans. It had gone open-circuit and reduced the
audio. But the CRO didn't pick it up.
There were other occasions when he tried to use the CRO but the result
was the same. It didn't really help.
If you are a highly qualified audio technician and know the waveforms
you should be getting at each location, it will be a completely different
situation to trying to find an unknown fault in an audio stage. Sometimes
an audio waveform is very messy when viewed on a CRO and yet the audio is
quite clean. Other times the waveform appears to be quite good and yet
the signal is distorted.
If the CRO was the answer to these problems, I would have no
hesitation in suggesting you buy one, but it can sometimes create more
problems than it solves.
To produce an audio waveform suitable for viewing on a CRO, you have
to inject the stage with a steady waveform such as from a function
generator or sine-wave oscillator. You cannot simply supply it with a
signal from a radio station as the signal will be varying in amplitude
and changing in frequency. The CRO will not be able to “lock in” and
produce a stationary waveform.
You cannot work on a display that is constantly moving. This type of
display is only suitable for amusement at a science exhibition. The
screen must be perfectly stationary so you can view it and take
You need to measure the output and compare it to the input.
This is where a dual trace CRO comes in handy. On this type of CRO you
will be able to display both the input and output at the same time and by
super-imposing them on top of each other. You will then be able to see the
Alternatively you can display one waveform above the other and pick
out the differences.
If you only have a single trace CRO, you will need to switch from the
input to output as quickly as possible so the differences can be
Even when you see a difference you will have to work out if it
represents a fault.
An audio stage does not always produce distortion due to clipping or
over-drive, it sometimes sounds `hollow' or `tinny' due to the coupling
capacitors being too small or dried out. These types of faults will not
be picked up on a CRO and I suggest you save your money at this stage and
buy the Mini Bench Amplifier.
It will enable you fix audio faults very easily and save you a lot of
THE LM 386
The LM 386 is a high power op-amp. It is used to drive a speaker.
The inverting input has been connected to the negative rail and the
non-inverting input has been connected to a capacitor. Resistors inside
the chip bias this input so that it only requires about 7mV before the
chip turns on. This voltage is called the off-set voltage.
When a signal is applied to the “+” input, the chip amplifies the
waveform and the result appears on pin 5. The gain of the chip depends on
the impedance of the path between pins 1 and 8. We have placed a variable
impedance, made up of a 22u and 10k pot between these pins and by varying
the resistance of the pot, the gain of the chip will be adjusted.
The gain can be adjusted from 30 to 200 and these figures are shown on
the overlay of the board.
FIXING AUDIO STAGES
As we said, there can be lots of problems with audio stages. Sometimes
they develop over a period of time, or they can be present from the
moment the amplifier is assembled. You can also get intermittent faults,
drop outs, squealing, motor-boating, distortion or simply lack of gain.
The amplifier presented in this article is used as an audio probe by
listening to the loudness and quality of the audio going into the stage
under test and comparing it to the audio emerging from the output of the
You do this by putting the earpiece near your ear and
listening carefully - that's why the probe has two long leads.
We could write a book on fixing audio stages but to reduce it to one
page, here is the approach:
The simplest situation is a single transistor amplifier with a
The first thing to do is replace the transistor. Even though
transistors are very reliable devices, you may have overheated it and
this will cause the device to have a different gain and thus the voltages
on the stage will not allow the signal to be processed correctly (you can
put it back later if it is not the cause of the problem).
The next thing is measure the voltage on the collector. Ideally it
should be half-rail. This allows the transistor to turn on and off THE
MAXIMUM AMOUNT and thus give the stage the maximum gain.
To carry out any more investigation on the stage you will need a copy
of the circuit diagram. This will let you know how the transistor is
biased and may give details of the voltages at the various locations.
Next look at the electrolytics. These can be inter-stage devices,
decoupling or emitter bypass capacitors. They can dry-out and lose their
capacitance or go open (very rarely) or go short-circuit (very rare).
Tantalums can also go short-circuit as they are susceptible to high
voltage spikes that puncture their ceramic substrate.
If the transistor has an emitter by-pass capacitor in the form of an
electrolytic across the emitter resistor, the stage gain will be severely
reduced if the capacitor (electrolytic) has lost its capacitance (dried
A faulty inter-stage capacitor (one that connects the output of one
stage to the input of the next) can be checked by placing the probe one
side of the capacitor, then the other. If the audio level drops
considerably, the capacitor is not passing the signal and may be faulty.
If you have replaced the transistor with another type, the voltage on
the collector may be different to that specified.
If it is lower, the transistor has a higher gain and the base-bias
resistor must be increased. If it is higher than expected, the base-bias
resistor must be decreased.
This only applies to simple self-biasing stages, where the base-bias
resistor sets the collector voltage for the stage.
Resistors rarely give trouble except if they are of an old style or in
a position where they get hot.
If hum is present on the audio, the fault will lie in the filtering of
the power supply. If a squeal similar to a feed-back squeal, (as heard
when a microphone is too near the speaker of an amplifier), the fault can
be in the decoupling capacitor. This is generally a small value
electrolytic (10u to 100u) near the stage it is protecting and will be
associated with a low value resistor on the power rail. The electrolytic is
connected across the power rails.
This electrolytic can also produce a fault similar to the putt-putt-putt
of a motor boat exhaust system, bubbling through water.
The Mini Bench Amp has a volume control in the form of a gain control,
to vary the output volume from the earpiece. The approximate gain is
marked around the control.
An additional probe can be connected to the board via a small socket
and this will allow the Mini Amplifier to be brought up to your ear so
you can listen to the audio.
Everything fits on the PC board supplied in the kit. The earpiece is
plugged into a mono socket on the board.
The Mini Bench Amplifier
The IC socket is fitted so that the notch at one end corresponds to
pin 1 and covers the cut-out on the overlay. This helps when fitting the
IC at the end of assembly.
The cathode of the LED is identified by a flat side on the body of the
LED and this is the line on the symbol on the overlay.
Mini Bench Amp
$5.50 MAX post
1 - 1k|
1 - 5k mini pot with shaft
1 - 10k horizontal trim pot
1 - 100n monoblock capacitor
1 - 22u 16v PC mount electrolytic
2 - 100u 16v PC mount electrolytic
1 - LM 386 N1 400mW amp chip
1 - 8 pin IC socket
1 - 8R earpiece
1 - 3mm red LED
1 - battery snap
1 - 9v battery
1 - SPDT slide-switch
1 - mono, switched 2.5mm socket
1 - paper clip or long nail for probe
1 - black alligator clip
1 - red alligator clip
1 - 25cm red hook-up wire
1 - 25cm black hook-up wire
1 - pin and socket for lead
1 - MINI BENCH AMP PC Board
MINI BENCH AMP can be obtained from Talking Electronics:
The three electrolytics have a line down one side indicating the
negative lead. The board has the positive lead marked with a small plus
The only other item needing a little care is the battery snap. It is
removed from the plastic covering and the two lengths of wire snipped
off, the two eyelets are tightened by hammering with a centre-punch. It
is then fitted as shown in the following three diagrams:
The bottom of the board is shown. The wire is looped from the
bottom and twisted. Note the polarity of the battery snap.
The battery snap is pushed up to the board and the twisted wires
are cut short.
Both the top and bottom of the board are soldered to the battery
snap to keep it firmly in position.
The 9v battery is clipped directly to the board via the battery snap.
The optional probe uses red hookup wire and an alligator clip otherwise
use a paper-clip or nail soldered to the end of the board.
The paper clip must not be cut with side-cutters as it is made from
hardened steel and will damage the cutters. The only way to
cut the clip is to file a niche in the wire and bend it back and forth
until it fractures. This probe is then soldered directly to the board
with some wire loops that add strength. It is called the active lead as it
goes to the ‘active’ input of the chip.
The ground lead uses the black hook-up wire and has an alligator clip
soldered to it.
All the other components are fitted close to the board and leads
are snipped close to the board after soldering. Fit the IC and 9v
battery and the project is complete.
IF IT DOESN'T WORK
Switch the Mini Bench Amp on and turn the gain control to maximum. Touch
the active probe with your finger. You should hear a slight buzz from the
speaker. This is a quick test to show the project is working. If nothing
is detected, you should follow these steps:
If the power LED doesn't come on, the most probable cause is a flat
battery or the battery terminals not making contact.
Also check the placement of the LED as it may be around the wrong way.
Next check the current taken by the circuit, across the switch (with
the switch in the OFF position). It should be about 10mA.
If no sound comes from the earpiece, measure its resistance with a
multimeter. It should produce a slight `click' when you do this and
measure about 8 ohms.
Check that pin 1 of the IC is near the cut-out on the overlay and see
that all the pins of the chip are entering the socket. Sometimes a pin
bends over and does not make contact. Also make sure all the pins of the
socket are soldered to the board. This applies to all the other
components. Finally, make sure the positive of the battery goes to the
positive rail on the board and the negative goes to the negative rail.
There is little else that can go wrong and the project should be
working by now.
USING THE MINI BENCH AMP
All you have to do is connect the ground lead to the project you are
testing, switch the Mini Bench Amp on and also the project you are testing.
Use the probe or the active lead to probe various points on the
project under test and listen for the audio. The gain control on the
Mini Bench Amp is very similar to a volume control and will allow you to hear
the audio without too much over-drive.
Most amplifying stages have a gain of about 50 - 70. Some will have a
gain of about 100 but this is about as high as you will get.
It is impossible to describe how to determine if a stage has high or
low gain, merely by listening to it. The only way to work out a gain
factor is to use a CRO.
One clever way to fault-find a project is to get another identical
unit and compare one with the other.
To do this you need to set both beside each other and join the
ground lines together. Turn them both ON and you can then probe each
stage and compare one with the other.
If you have had the frustration of trying to diagnose an audio stage, you
will find this project absolutely essential.
I hope you get to use it soon.